POWER GENERATION

SAM825k-AMF

Automatic controller for generator sets
Automatic Mains Failure (AMF)

SAM825k-AMF
Ask for quotation
SAM825k-AMF

SAM825k-AMF controllers are high-performance, complete, automatic, and configurable instruments, useful for controlling generator sets in emergency automatic mains failure (AMF) installations.

SAM825k-AMF controllers automatically start and stop generator sets, protect them by means of the connected and controller-generated alarms, and visualize the most relevant values. They carry out the general coordination of the operation and the switching of the consumers from the Mains to Generator and vice versa.

MAIN FEATURES

  • Nº BASIC FEATURES INDEX
    1 Display Graphic/Transflective/3.2″ (outside view)
    2 Protection IP65
    3 Buzzer Built-in buzzer
    4 Safety key switch  Mode selection:OFF / MAN / AUTO
    5 Electrical measurements 3 phases true RMS: V / Amp / kW / kVAr/ KVA
    6 Sensors %Fuel / Temperature / Oil Pres. / rpm
    6 Communications Canbus/ RS485 / Ethernet / GSM
    7 Weekly scheduler clock 4 dayly slots.
    8 Fresstanding / AMF / Redundant generators
    9 Asociated software Configuration/Control/Monitoring
  • Nº BASIC FUNCTION INDEX
    1 Pre-Crank process Starter-Preignition/Gas Ramp/Prelube/Turn on ECU
    2 Engine alternator priming D+
    3 Engine start process Crank engine/Bendix
    4 Fuel management Electrovalve/shut down solenoid
    5 Fuel transfer pump activation Fuel tank level measurement
    6 Heating element activation Coolant temperatura measurement
    7 Engine idle management Idle/rated speed
    8 Cooling water valve management Engine running function
    9 Siren activation Externarl optional installation
    10 Common alarms output activation Remote communication
    11 Configurable outputs Control and warnings
    12 Engine-alternator system protection By enabled alarms
    13 Man-machine interface using front display 3.2″ graphic/Transflective
    14 Communications USB / RS485 / ETHERNET / CANBUS / GSM
  • Nº BASIC FUNCTION INDEX
    1 Pre-Crank process Starter-Preignition/Gas Ramp/Prelube/Turn on ECU
    2 Engine alternator priming D+
    3 Engine start process Crank engine/Bendix
    4 Fuel management Electrovalve/shut down solenoid
    5 Fuel transfer pump activation Fuel tank level measurement
    6 Heating element activation Coolant temperatura measurement
    7 Engine idle management Idle/rated speed
    8 Cooling water valve management Engine running function
    9 Siren activation Externarl optional installation
    10 Common alarms output activation Remote communication
    11 Configurable outputs Control and warnings
    12 Engine-alternator system protection By enabled alarms
    13 Man-machine interface using front display 3.2″ graphic/Transflective
    14 Communications USB / RS485 / ETHERNET / CANBUS / GSM
  • Nº MECHANICAL MEASUREMENT INSTRUMENTS
    1 Oil pressure. Sensor or Canbus Range: 0 bar-10 bar ±0,5 bar
    2 Coolant temperature. Sensor or Canbus Range: 0ºC – 150ºC ±1ºC
    3 Fuel tank level. Sensor Range: 20% – 100% ±5%
    4 Engine speed . Terminal W, Pick-Up or Canbus rpm
    5 Total fuel consumed. Canbus Liters
    6 Instant fuel consumption . Canbus Liter/Hour
    7 Current engine torque. Canbus %
    8 Torque demand. Canbus %
    9 Coolant level. Canbus %
    10 Oil level. Canbus %
    11 Oil temperature. Canbus ºC
    12 Coolant pressure %